What are the UK regional settings for Linksys & Sipura adaptors?
If you get a generic Linksys or Sipura adaptor or reset one, the adaptor will be configured for the US telecom system. This means that phones using the adaptor will act like US phones unless we make some changes to the settings. This guide should work for most Linksys & Sipura devices.
First you will need to login to your Linksys or Sipura adaptor by typing the IP address of the device into your browser, for a Sipura add the "admin" and "Advanced" modes.
An example for each follows (X's represent the IP address of the Sipura):
If your using a Linksys device then you will need to enter this:
(X's represent the IP address of the Linksys)
The settings for using a Linsys or Sipura adaptor with a PBX are beyond the scope of this guide, so we assume that by following this guide, you are simply connecting analogue or digital phones and not a PBX or call centre switching software.
United Kingdom Regional Settings:
Dial Tone: 350@-19,440@-22;10(*/0/1+2)
Second Dial Tone: 420@-19,520@-22;10(*/0/1+2)
Outside Dial Tone: 420@-22;10(*/0/1)
Prompt Tone: 520@-19,620@-22;10(*/0/1+2)
Busy Tone: 400@-20;10(.375/.375/1)
Reorder Tone: 400@-20;10(*/0/1)
Off Hook Warning Tone: 480@-10,620@-16,1400@0,2060@0,2450@0,2600@0;60(.2/0/1,.2/0/2);240(.1/.1/3+4+5+6)
Ring Back Tone: 400@-20,450@-20;*(.4/.2/1+2,.4/2/1+2)
Confirm Tone: 600@-16;1(.25/.25/1)
SIT1 Tone: 950@-16,1400@-16,1800@-16;20(.330/0/1,.330/0/2,.330/0/3,0/1/0)
SIT2 Tone: 914@-16,1371@-16,1777@-16;20(.274/0/1,.274/0/2,.380/0/3,0/4/0)
SIT3 Tone: 914@-16,1371@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)
SIT4 Tone: 985@-16,1371@-16,1777@-16;20(.380/0/1,.274/0/2,.380/0/3,0/4/0)
MWI Dial Tone: 350@-19,440@-22;10(.75/.75/1+2)
Cfwd Dial Tone: 350@-19,440@-22;10(.75/.75/1+2)
DND Dial Tone: 350@-19,440@-22;10(.75/.75/1+2)
Holding Tone: 600@-20;*(.1/.1/1,.1/.1/1,.1/2.2/1)
Conference Tone: 350@-22;20(.1/.1/1,.1/9.7/1)
Secure Call Indication Tone: 397@-19,507@-19;15(0/2/0,.2/.1/1,.1/2.1/2)
Feature Invocation Tone: 350@-16;*(.1/.1/1)
Distinctive Ring Patterns
Ring1 Cadence: 60(.4/.2,.4/2)
Ring2 Cadence: 60(1/2)
Ring3 Cadence: 60(.25/.25,.25/.25,.25/1.75)
Ring4 Cadence: 60(.4/.8)
Ring5 Cadence: 60(2/4)
Ring6 Cadence: 60(.2/.4,.2/.4,.2/4)
Ring7 Cadence: 60(.4/.2,.4/.2,.4/4)
Ring8 Cadence: 60(0.25/9.75)
Distinctive Call Waiting Tone Patterns
CWT1 Cadence: 30(.1/2)
CWT2 Cadence: 30(.25/.25,.25/.25,.25/5)
CWT3 Cadence: 30(.1/.1, .1/.1, .1/9.7)
CWT4 Cadence: 30(.1/.1,.3/.1,.1/9.3)
CWT5 Cadence: 1(.5/.5)
CWT6 Cadence: 30(.1/.1,.3/.2,.3/9.1)
CWT7 Cadence: 30(.3/.1,.3/.1,.1/9.1)
CWT8 Cadence: 2.3(.3/2)
Ring and Call Waiting Tone Spec
Ring Waveform: Trapezoid
Ring Frequency: 25
Ring Voltage: 70
CWT Frequency: 400@-10
Control Timer Values (sec)
Hook Flash Timer Min: .06
Hook Flash Timer Max: .2
Callee On Hook Delay: 0
Reorder Delay: 5
Call Back Expires: 1800
Call Back Retry Interval: 30
Call Back Delay: .5
VMWI Refresh Intvl: 0
Interdigit Long Timer: 6
Interdigit Short Timer: 3
CPC Delay: 2
CPC Duration: .1
Time Zone: GMT
FXS Port Impedance: 370+620||310nF
Daylight Saving Rule: start=3/-1/7/2:0:0;end=10/-1/7/2:0:0;save=1:0:0
FXS Port Input Gain: 0
FXS Port Output Gain: 0
DTMF Playback Level: -16
DTMF Playback Length: .1
Detect ABCD: yes
Playback ABCD: yes
Caller ID Method: ETSI FSK with PR(UK)
FXS Port Power Limit: 3
Caller ID FSK Standard: v.23
Feature Invocation Method: Default
More Echo Suppression: No
UK Dial Plan for use with Voipfone.co.uk?
Below you will find a UK dial plan for use with Voipfone, in fact it is my dial plan for the city of Swansea. It is setup to allow calls to local numbers without the need to enter my area code every time I call a local number, it is also set to bar calls to 090 premium rate calls.
Take a look at it below:
Now read on for an explanation of what each part of the above dial plan actually does!
This part |112SO|123SO|150SO|152SO|153SO|154SO|155SO|156SO|158SO|166SO|999SO|1471SO|1571SO|1572SO refers to Emergency services and Voipfone numbers such as 154 or 155 so that when you dial say 154 to check your balance the call is connected without any delay.
This part <:01792>[2-8]xxxxxS0 refers to local numbers, it saves you having to dial your local area code every time you call a local number.
(You will need to change 01792 located in the above to your local area code.)
This part 0[1-9]xxxxxxxxxS0 refers to national numbers and numbers like 0800, 0870, 0871 etc...
This part *x. allows calls to be made starting with a *, these include numbers like *69 or sip numbers like *123456789
This part 00[1-9]x. refers to international calls.
This part 090x! refers to premium rate calls, this stops calls being made to any premium rate numbers.
A dial plan always starts with a ( and ends with a ) the | symbol located in the above dial plan is used to seperate each dial plan command!
For a more indepth information about dial plans and how to create one yourself see here: http://www.netphonedirectory.com/pap2_dialplan.htm
Or here: http://voip.wikispaces.com/DialPlans#tocDialPlans9
UK Recall function
Also on a last note, a UK phone's recall button does not work with the factory defaults. This is because it is set to long for use on UK phones, if you want to use the recall function then set the Hook Flash Timer Min located under the regional tab to the following:
Hook Flash Timer Min: .06
Hook Flash Timer Max: .2
If you know of any other settings for the Linksys or Sipura range then PM me and I'll add them!
Below you will find the manual configuration for the Voipfone feature codes listed above:
I recommend using the Voipfone codes and not the default one's as this can make things easier when getting help from support or if other users are likely to browse the voipfone guides in order to find out how to enable or disable a feature.
You will not need to change anything if your adapter was supplied by Voipfone as it will be configured correctly automatically.
Log in to your pap2/pap2T as an admin, and under the regional tab scroll down to the Vertical Service Activation Codes list...
Do Not Disturb feature, this stops all incoming calls by giving an engaged tone.
78# Turn on DND function (blocks inbound calls)
DND Act Code: 78#
Disables the Do Not Disturb feature
79# Turn off DND function
DND Deact Code: #78#
Call waiting, while in a call should someone dial your number instead of receiving an engaged tone you will receive a notification of the new call and their caller id will display on screen.
*43# turn on call waiting
CW Act Code: *43#
Disables call waiting.
#43# turn off call waiting
CW Deact Code: #43#
Diverting all incoming numbers directly to another number or extension.
*21*<number># diverts calls to the entered number
Cfwd All Act Code: *21*
Disables the divert of all incoming calls.
#21# turns off divert
Cfwd All Deact Code: #21#
Diverting all calls when line is busy, if your in a call you can divert any incoming calls whilst the line is engaged to a number or extension of your choice.
*67*<number># diverts calls on busy to the entered number
Cfwd Busy Act Code: *67*
Disables the divert of all engaged/busy calls.
#67# turns off divert on busy
Cfwd Busy Deact Code: #67#
Diverting calls if nobody answers, if nobody is around to answer a call divert it to a number or extension of your choice.
*61*<number># diverts calls on no answer to the entered number
Cfwd No Ans Act Code: *61*
Disables the divert of unanswered calls.
#61# turns off divert on no answer
Cfwd No Ans Deact Code: #61#
Now for transfers......
R(Recall) 9# <number> does an unattended transfer of a call to the entered number.
Blind Transfer Code: 9#
R, dial the second person. Once speaking press R again, this created a 3 way conference. Hang up to transfer the call.[/quote]
No configuration required for attended transfers
- Information & Feedback
- - Voipfone Status Page
- - News & Product Announcements
- - Feedback & Bug Reports
- Help and Support
- - Voipfone General Information and FAQs
- - Hardware Support
- - - Phone Setup Guides
- - - - Snom Phones
- - - - Siemens Phones
- - - - Linksys Phones
- - - Adaptor Setup Guides
- - - Network Setup Guides
- - Softphone Support
- - - Softphone Setup Guides
- - - Download Zoiper Softphone
- - Voipfone Virtual PBX Support
- - Routers, Firewalls & NAT
- - Broadband Support
- - - Getting Started, Router Config
- - - Voipfone Broadband FAQ
- - Asterisk and other hardware PBX Support
- - CRM (Customer Relationship Management) Integration
- - Voipfone Address Book Dialler (TAPI Plugin)
- - Browser Dialler Plugins
- Voipfone Community
- - Voipfone General Discussion Forum
- - Suggestion for New Voipfone Products, Services and Features
- - - Vote for the Voipfone features you want us to develop
- - Voipfone Trading Post
- - Virtual Assistants Forum
- - Transcription Services
Who is online
Users browsing this forum: No registered users and 0 guests